Tester Volt Curent

Batteries are blamed for most cell phone problems. To satisfy the customer, batteries are replaced, often to have the fault recur. The Cadex C5100 battery analyzer assists by allowing to check the battery at storefront with a 30-second test. Testing mobile phone batteries has never been so easy.
Deploying the C5100 in your store will:
Improve customer care
Increase revenue and reduce costs
Protect the environment by discarding fewer batteries

The D100, is adapted to a full range of chemistries (LiPo, LiFe, LiIon, NiMH, NiCd and PB) and comes with a comprehensive set of leads making it fully-prepared for practically any battery type. This charger is specially designed to cater for the higher end user, but with the aid of a simple-to-use interface and a complete set of instructions, this charger is by no means limited to experts.

This charger features:
► Two independent charging circuits (dual 2x100W output on DC (or with power supply) and 100W can be distributed across 2 channels on AC)
► Terminal voltage control
► Re-Peak mode for NiMH/NiCD batteries
► Battery meter
► Battery internal resistance meter
► PC communications

This chargers comes with two XH balance boards, XT60 with crocodile clips, two XT60 charge leads, two deans charge leads, and an AC power cord with crocodile clips for DC.

The D100 has been created with automated safety precautions, including a charging current limit, capacity limit, temperature threshold and processing time limit.

This charger is also compatible with both iOS and Android smart phones via a Wi-Fi Module (sold separately), making operation easier than ever. Specifications:
Input voltage: AC 100-240V / DC 11-18V
Charging circuit: AC Input 100W / DC Input 2x100W
Discharge circuit: 2x10W
Charging current: 0.1-10A
discharge current: 0.1-5A
Balancing Leakage Current Port: Max 200mAh / cell
Slow Charging current: 20mA-300mA & OFF
LiPo / LiFe / LiIon / LiHV batteries: 1-6 pcs.
NiMH / NiCd batteries: 1-15 pcs.
Voltage Battery Lead (PB): 2-20V
Dimensions: 163x153x72mm
Weight: 975g

The Extech BT100 is a Battery Capacity Tester. Product can be used to test the condition of batteries quickly and easily. As an AC milliohm-meter, the tester measures DC voltage and AC resistance while the battery is in use, helping to save time on repetitive testing trials or large quantities of batteries. Specifications
Range Resolution Basic Accuracy
Resistance 40mΩ, 400mΩ, 4Ω, 40Ω 10µΩ, 100µΩ, 1mΩ, 10mΩ ±(1% reading ± 10d)
Voltage 4V, 40V 1mV, 10mV ±(0.1% reading ±6d)
Max Input Voltage 50VDC
Manual Datalogging 999 sets
Continuous Datalogging 9600 sets
Power 6 AA batteries
Battery life 7 hours
Dimensions 9.75 x 4 x 1.75" (250 x 100 x 45 mm)
Weight 17.5oz (500g)

Brand DT
Model 830D+
Quantity 1
Color Orange + black
Material ABS
LCD Display 2"
Features Portable
Max. Display 9999
DC Voltage 200mV / 2V / 20V / 200V / 600V +/- (0.5%+3)
AC Voltage 200V / 600V +/-(0.8%+5)
DC Current 200uA / 2mA / 20mA / 200mA / 10A +/-(1.0%+3)
Resistance 200 / 2K / 20K / 200K / 2M +/-(0.8%+3) ohm
Power Supply 1 x 6F22 battery (included) / 9V
Packing List 1 x Multimeter
2 x Test leads (66cm cable)
Dimensions: 4.33 in x 2.60 in x 1.30 in (11.0 cm x 6.6 cm x 3.3 cm)
Weight: 5.40 oz (153 g)

Product overview: Fluke 107 Pocket Digital Multimeter
The Fluke 107 is a compact, palm size easy-to-use digital multimeter made to fit the way you work. It is the perfect first-pass troubleshooting tool; small enough to fit in a shirt pocket yet tough enough to withstand daily use, including a 1-meter drop test. For everyday applications where true-rms accuracy isn’t needed, the Fluke 107 delivers reliable measurements time after time. With a CAT III 600 V safety rating, you don’t need to compromise safety. The Fluke 107 offers a comfortable grip, weighs only 200 g, and is easy to carry.

Fluke 107 measurement test functions AC and DC voltage
AC and DC current
Resistance
Capacitance
Diode
Frequency and duty-cycle
Fluke 107 comes ready to work
The Fluke 107 comes with a TL75 Hard Point™ Test Lead Set. It’s one pair (red, black) of 48 inch (1.22 meter) test leads with right-angle, shrouded banana plugs. The meter also includes a SmartStrap™ intelligent magnetic multi-purpose lanyard that lets you hang the Fluke 107 from any ferrous surface or support the meter at an angle for easy viewing.

Product overview: Fluke 110 True-rms Digital Multimeter Compact true-rms meter for accurate electrical installation and troubleshooting TL75 Hard Point™ Test Lead Set with protective caps. The Fluke 110 is a versatile multimeter for electrical measurements and troubleshooting. Trusted by residential and commercial electricians for troubleshooting and maintenance. The 110 is for professional use, where true-rms accuracy is needed.
Key product capabilities True-rms ac voltage for accurate measurements on non-linear signals
Large white LED backlight to work in poorly lit areas
Resistance and continuity
Min/Max/Average to record signal fluctuations
CAT III 600 V safety rated

Specifications Range
Model UT151F , ut-151f
DC Voltage (V) 200mV/2V/20V/ 200V/600V ±(0.05%+3)
AC Voltage (V) 200mV/2V/20V/ 200V/600V ±(0.5%+10)
DC Current (A) 2mA/20mA/200mA/ 10A ±(0.5%+5)
AC Current (A) 2mA/20mA/ 200mA/10A ±(0.8%+10)
Resistance (Ω) 200Ω/2kΩ/20kΩ/ 200kΩ/2MΩ/20MΩ ±(0.3%+1)
Capacitance (F) 20nF/ 200nF/ 2μF/ 20μF ±(4%+20)
Frequency (Hz) 20kHz ±(1.5%+5)
Features
Display Count 20000
Manual Range √
Diode √
Auto Power Off √
Continuity Buzzer √
Low BatteryIndication √
Data Hold √
Input Impedance for DCV ≥10MΩ √
General Characteristics
Power 9V battery (6F22)
LCD Size 63mm X 29mm
Product Color Red and grey
Product NetWeight 300g
Product Size 186mm X 91mm X39mm
StandardAccessories Battery, test lead
Standard Individual Packing Gift box, English manual

New UT61+ series are reliable true RMS digital multimeters with display counts 6000
(UT61B+/D+) and 22,0 0 0 (UT61E+). It can measure up to 10 0 0V AC/DC . Equipped with
audible and visible alarm, this series can provide warning expecially when measuring
high voltage/current and temperature.
UT161 series are CE cer�fied, suitable for the European market.
● True RMS
● Data hold/backlight
● Max/Min/Rela�ve mode
● USB communica�on
● Diode/con�nuity test
● NCV (audible/visual alarm)
● LoZ ACV (UT61D+/UT161D)
● LPF ACV/ACV+DCV/Transistor hFE (UT61E+/161E)
● Peak Hold (UT61D+/61E+/161D/161E)

Brand YX
Model 9205A+
Quantity 1
Color Orange + black
Material ABS
LCD Display 2,7"
Features Portable
DC Voltage 200mV / 2V / 20V / 200V / 600V +/- (0.5%+2)
AC Voltage 200V / 700V +/-(0.8%+3)
DC Current 200mA / 2mA / 20mA / 200mA / 10A +/-(1.2%+2)
Resistance 200Ω / 2K / 20K / 200K / 2M +/-(0.8%+2) ohm
Power Supply 1 x 6F22 battery (included) / 9V
Packing List 1 x Multimeter
2 x Test leads (66cm cable)
Dimensions: 31,5mm x 91mm x 189mm
Weight: 280g

PowerJive USB Voltage/Amps Power Meter Tester Multimeter, Test speed of chargers, cables, capacity of power banks. Details:
Sepecification: Input Voltage: 3-15V
Input Current: 0.05-3.5A
Measurement error: ±1%
Capacity range : 0-19999mAh Functions: When the display is closed, click the button to open the display.Then click the button turns to view data in each group,click one time, the screen will display next group of data, the group of digital flash 5 seconds, after 5 seconds without any operation , the screen will come back to show the current group data. Double click the button to switch to the next group of capacity data record; Holding button (about 2-3 seconds) , current data will be deleted ;
5 minutes without any operation, the display backlit automatically shut down.
When the voltage is over than 13V or lower than 4.6V, the voltage display data flashing (frequency 1Hz), buzzer sound alarm (D-, every 5 seconds); when the voltage is higher than 15V, USB port will be shut down automatically in order to protect the device , and Buzzer will alarm (Sound: "D – D – D" repeated every 5 seconds).
When output current is over 3.1A, the electric current data will flash (1Hz frequency), buzzer will alarm (D-, every 5 seconds); when the output current is over 3.5A, USB port will be shut down automatically in order to protect the device , and buzzer will alarm ( Sound: "D – D – D" repeated every 5 seconds)
Over voltage (more than 15V) or over current (more than 3.5A) shut off output, to prevent the twice damage to the load device without monitoring, this item have to be shut down( it means just take out from power) then use again. Notes: Input Voltage must not over 15V, otherwise it may cause permanent damage to the equipment.
If you use "USB load resistance" (sell separately), must not work for a long time during electric current is over 3A;
To ensure the equipment universal fast charging automatic recognition function, power supply voltage shall be 4.6~15V.

Power USB Tester Tail KWS-10VA Voltage Current Detector.
Details:
Voltage: 3 - 9V ± 1%
Current: 0 - 3A ± 1%
Specification Brand Name: VKTECH
Operating temperature: Normal
DIY supplies: Electric
Accuracy class: Accurate
Display type: Digital only
Dimensions: 59 * 23 * 14mm
Model Number: Volt Meter
Power supply: USB
Operating Range: U = 3 ~ 7.5V I = 0 ~ 2.5A
Full scale drop:: (When measuring current) 200mV
Measuring Range: Voltage 10mV current 1mA