PROCOM

Adaptor FME-N connector

Original battery cover Samsung i9500 Galaxy S4, i9505 4G LTE Blue

Low loss cable RF Procom 10MFMEXLL

Original battery SP3676B1A Samsung Lion 7000mah Bulk.
Compatible with Samsung P5100 Galaxy Tab 2 10 1, P7500 Galaxy Tab 10 1, P7510, P5110 Galaxy Tab 2 10 1, N8000 Galaxy Note 10 1, N8020 Galaxy Note 10.1 LTE, N8010 Galaxy Note 10.1

ORDERING DESIGNATIONS
TYPE
PRODUCT NO.

YA 2100 130001553

Top of page

SPECIFICATIONS
ELECTRICAL

MODEL YA 2100
ANTENNA TYPE 9-element Yagi-antenna
FREQUENCY 1900 – 2200 MHz
IMPEDANCE Nom. 50 Ω
POLARIZATION Linear

(vertical or horizontal dep. on orientation)

GAIN 10 dBi 8 dBd
FRONT-TO-BACK-RATIO ≥ 15 dB
HALF-POWER BEAMWIDTH Approx. 35° (E-plane)

Approx. 45° (H-plane)

BANDWIDTH 200 MHz
SWR ≤ 1.8 @ 1.9 - 2.2 GHz
MAX. POWER 25 W
MECHANICAL

MATERIALS Antenna: Gold aludine, Aluminium
Fittings: Stainless steel
COLOUR Aludine “gold”
TOTAL LENGTH 570 mm
MAX. ELEMENT HEIGHT 100 mm
WEIGHT 300 g (incl. bolts)
CONNECTORS FME-connector

(cable to be ordered separately)

MOUNTING On 30 – 50 mm dia. mast tube

The CXL 2-3 GHz is an ultra broad-banded, 0 dBd, vertically polarized, omnidirectional rod-type base station and marine antenna for the 2 - 3 GHz band.
The 1” revolving nut mounting system is standard throughout the marine sector, and several different mounting brackets are available, making it possible to install the antenna either on the masthead by use of FLG or SMR 2, side-mounted on the mast (SMR 1) or mounted on a cross-beam (FLG). Also, the antenna can be mounted on deck or rooftop by means of the FLG.
The higher the antenna is mounted, the better coverage. Avoid mounting the antenna parallel to or in the neighbourhood of other metal parts, such as masts, supporting wires etc., otherwise the SWR and the radiation pattern may be strongly influenced.
A conical glass fibre tube completely encloses the carefully designed radiating element to ensure long dependable service in all climates.

Vertically polarized, omnidirectional base station and marine antenna.
Approximately 3 dBd gain.
Provided with the sturdy “LW” mast mount – a lightweight, multipurpose, epoxy-coated mounting bracket made of non-corrosive aluminium.
The accompanying U-bolts and fittings are made of stainless steel.
To be mounted on vertical or horizontal mast tubes, 16 to
54 mm in outer diameter.
The cable can be led either on the outside or along the inside of the mast tube.
Large bandwidth with respect to both SWR and gain.
Highly suitable for duplex operation with large spacing between the TX and the RX frequencies.
The antenna element is sealed in a high-quality, conical glass fibre tube.
All metal parts in the antenna are DC-grounded to reduce the noise caused by atmospherical discharge. Consequently, the antenna shows a DC-short across the coaxial cable.
The CXL 2400-3LW/… is a vibration-proof, lightweight, slim-line, corrosion resistant, modern style base station and marine antenna.

ORDERING DESIGNATIONS
TYPE NO.
FREQUENCY

CXL 2000-6LW/l 1900 – 2050 MHz
CXL 2000-6LW/m 2000 – 2150 MHz
CXL 2000-6LW/h 2100 – 2200 MHz

SPECIFICATIONS
ELECTRICAL

MODEL CXL 2000-6LW/...
ANTENNA TYPE Coaxial, colinear antenna, broadbanded
FREQUENCY Models within 1900 – 2200 MHz
IMPEDANCE Nom. 50 Ω
POLARISATION Vertical
GAIN 8 dBi 6 dBd
BAND WIDTH ≥ 150 MHz @ SWR ≤ 2.0
SWR ≤ 2.0, typ. ≤ 1.5
MAX. POWER 100 W
ANTISTATIC PROTECTION All metal parts DC-grounded
(Connector shows a DC-short)
MECHANICAL

TEMP. RANGE -30°C → +70°C
CONNECTOR N-female
WIND SURFACE Approx. 0.033 m²
WIND LOAD Approx. 42 N @ 160 km/h
COLOUR Marine white
MATERIALS Shroud: Polyurethane coated glass fibre
Mounting bracket: Seawater resistant aluminium, epoxy-coated
Clamps: Stainless steel
TOTAL HEIGHT Approx. 1.2 m
DIA. IN TOP END 21 mm
DIA. IN BOTTOM END 23 mm
WEIGHT Approx. 800 g
MOUNTING On 16 to 54 mm dia. mast tube

DESCRIPTION

Vertically polarized, omnidirectional base station antenna and marine.
Approximately 6 dBd gain.
Provided with the sturdy “LW” mast mount – a lightweight, multipurpose, epoxy-coated mounting bracket made of non-corrosive aluminium.
The accompanying U-bolts and fittings are made of stainless steel.
To be mounted on vertical or horizontal mast tubes, 16 to
54 mm in outer diameter.
The cable can be led either on the outside or along the inside of the mast tube.
Large bandwidth with respect to both SWR and gain.
Highly suitable for duplex operation with large spacing between the TX and the RX frequencies.
The antenna element is sealed in a high-quality, conical glass fibre tube.
All metal parts in the antenna are DC-grounded to reduce the noise caused by atmospherical discharge. Consequently, the antenna shows a DC-short across the coaxial cable.
The CXL 2400-6LW/… is a vibration-proof, lightweight, slim-line, corrosion resistant, modern style base station antenna and marine.

Description

The DPF 70/6… is a 6-cavity duplex filter for duplex transceivers.
The DPF 70/6… can be adjusted within the complete 406 - 470 MHz band. The duplexer can be delivered in four different versions according to required duplex spacing. See also “Ordering information” below.
The DPF 70/6… is primarily intended for equipment where the Tx and Rx operate on single frequencies, but it can also, however with slightly reduced data, be used where the Tx and Rx operate on multi channels, i.e. within a certain port bandwidth. In the last case, factory-tuning is recommended.
The filter uses full-length ¼ λ cavities in a compact extruded aluminium housing. The chassis is made of passivated steel, and teflon insulation has been applied in the coaxial cables and in the connectors.
DPF 70/6... is coated with black vinyl to prevent corrosion.




Ordering Information

When ordering, please use the table to select the appropriate ordering designation for the desired filter type. If duplex Tx and Rx frequencies are stated when ordering, the duplexers are delivered factory-adjusted. If Tx and Rx frequencies are not stated, the filters are delivered non-adjusted.
Please Note

Special configurations of this filter type may be quoted on request. For instance, the filter can be delivered with other connector types, or with flying leads (e.g. RG 316 or RG 400 coaxial cable) terminated with connectors or for soldering-connection.